DrDAQ features
- Oscilloscope / spectrum analyzer
- Signal generator / arbitrary waveform generator
- Built-in sensors for light, temperature and sound
- Measure pH and redox — just plug in any standard electrode
- Sockets for external sensors including temperature and humidity
- 4 digital inputs and outputs (alarms, PWM, pulse counting)
- USB connected and powered
- Supplied with PicoScope 6 and PicoLog 6 software
- Supplied with PicoSDK Windows, Mac and Linux drivers
- Very low cost
Oscilloscope / spectrum analyzer
The DrDAQ oscilloscope input has a 100 kHz bandwidth, 8-bit resolution and four input ranges.
It is supplied with a full version of the PicoScope software, which offers high-end oscilloscope functions such as FFT spectrum analysis, mask limit testing, software-based filters and measurements.
Signal generator / arbitrary waveform generator (AWG)
The DrDAQ has a built in DC to 20 kHz function generator which when used with PicoScope software can output sine, square, triangle, ramp and DC voltage signals.
As well as the standard waveforms available from the function generator, custom waveforms can be created using the 10-bit 2 MS/s arbitrary waveform generator (AWG). AWG waveforms can be created or edited using the built-in editor, imported from oscilloscope traces, or loaded from a spreadsheet.
Sound level meter / sound waveforms
The built-in microphone can be used in two ways.
- Sound level meter / data logger with a 55 to 100 dB range using PicoLog 6
- Oscilloscope / spectrum analyzer with views of sound waveforms using PicoScope 6
Temperature sensor / data logger
A built-in sensor allows measures room temperature from –10 °C to +70 °C (14°F to +158°F)
The optional DD100 external sensor measures over a wider range of –10 °C to +105 °C (14°F to +221°F).
pH meter / redox meter
DrDAQ is compatible with standard pH electrodes allowing measurement and data logging over the full pH range. Since pH values are temperature-dependent you can use a DD100 temperature sensor and DrDAQ automatically corrects the pH value based on the temperature of the solution.
A kit is available containing a DrDAQ, pH electrode and temperature sensor. If you already own a DrDAQ, these sensors can be purchased separately.
The same high-impedance input used for pH can alternatively be used with redox sensors. The ability to measure and record pH and redox along with temperature and oxygen levels makes DrDAQ ideal for a wide range of chemistry and biology experiments.
External sensors
Three sockets are dedicated to external sensors. Simply plug in one of the optional external sensors and the software identifies the type of sensor and scales results with the correct units. Available sensors (see the Accessories tab) include temperature, oxygen, humidty and position.
Available accessories for the BNC inputs include ocilloscope probes, pH electrodes, redox sensors and a magnetic induction kit (educational experiment).
If you want to interface other sensors or design your own, full instructions are included.
Digital I/O, RGB LED and more!
The DrDAQ has 4 digital inputs / outputs. Each can be individually configured to be an input or alarm output, generate a PWM output signal or act as a pulse counter.
Resistance over a 0 to 1 MΩ range can be measured through the screw terminals. If used with resistive sensors (thermistors, light etc.) then the supplied software allows for scaling into the correct units.
Finally there is a software-controlled status LED that can be programmed to output any one of 16.7 million different colors using PicoScope 6.
Science experiments and education
As well as its use within industry, DrDAQ has proved itself to be popular both as an educational data logger (physics, chemistry, biology and electronics) and also as a versatile instrument for hobby use at home.
Visit our library of experiments for dozens of experiments you can perform with your DrDAQ.
Software drivers and example code
DrDAQ is supplied with full versions of both PicoScope and PicoLog software. It is also supplied with a wide range of drivers and example code to allow you to write your own programs and interface to third-party software.
Drivers are included for Microsoft Windows (7, 8 and 10), macOS, and Linux (including Raspberry Pi and BeagleBone).
Code examples are supplied for C, C++, C#, LabVIEW, Python and MATLAB.
Plug in and measure
DrDAQ simply plugs into the USB port of your PC – no external power supply is required. Everything you need to get started is included:
- DrDAQ data logger / oscilloscope
- PicoScope 6 software (download from website)
- PicoLog 6 software (download from website)
- PicoSDK drivers and example code (download from website)
- USB cable
- Manual